This groundwater is generally cold and clear. It can also come from melting snow in spring - putting pressure on your basement walls and floor - as well as downspouts, gutters, and grading issues directing rainwater toward your home. Excess groundwater entering your basement can come from a high water table or heavy rains, causing water buildup around and under your home’s foundation. Groundwater is water that accumulates in the soil and rock beneath the earth’s surface. These pumps protect your basement from flooding caused by excess groundwater. Sump pumps are small water pumps available in either pedestal or submersible models. Even though it may look similar or even identical, this is an ejector pump.īut what are ejector pumps, and how do they differ from sump pumps? This second pump is commonly found in finished basements near the washer and dryer. However, your basement may have what appears to be a second sump pump. Sump pumps are a common fixture in homes nationwide. Best Lawn Care Service for Service Dogs.Lighted Magnifying Glass That Stays Put.Half-bath group (water closet greater than 1. Half-bath group (1.6 gallon per flush water closet plus lavatory) Water closet (greater than 1.6 gallons per flush)įull-bath group with bathtub (with 1.6 gallon per flush water closet, and with or without shower head and/or whirlpool attachment on the bathtub or shower stall)įull-bath group with bathtub (water closet greater than 1.6 gallon per flush, and with or without shower head and/or whirlpool attachment on the bathtub or shower stall) Polyvinyl chloride (PVC) plastic pipe with a 3.25 inch O.D.ĭRAINAGE FIXTURE UNIT (d.f.u.) VALUES FOR VARIOUS PLUMBING FIXTURES TYPE OF FIXTURE OR GROUP OF FIXTURESīathtub (with or without a shower head or whirlpool attachments) Polyvinyl chloride (PVC) plastic pipe in sewer and drain diameters Polyvinyl chloride (PVC) plastic in IPS diameters TABLE P3002.3 PIPE FITTINGS PIPE MATERIALĪcrylonitrile butadiene styrene (ABS) plastic pipe in IPS diametersĪSTM D2661 ASTM D3311 ASTM F628 CSA B181.1Īcrylonotrile butadiene styrene (ABS) plastic pipe in sewer and drain diametersĪSME B16.4 ASME B16.12 ASTM A74 ASTM A888 CISPI 301ĪSME B16.15 ASME B16.18 ASME B16.22 ASME B16.23 ASME B16.26 ASME B16.29 Pipe fittings shall be approved for installation with the piping material installed and shall comply with the applicable standards indicated in Table P3002.3. Polyvinyl chloride (PVC) plastic pipe in IPS diameters, including schedule 40, DR 22 (PS 200) and DR 24 (PS 140) with solid, cellular core or composite wallĪSTM D2665 ASTM D2949 ASTM D3034 ASTM F1412 CSA B182.2 CSA B182.4 Polyvinyl chloride (PVC) plastic pipe in sewer and drain diameters, including PS 25, SDR 41 (PS 28), PS 35, SDR 35 (PS 46), PS 50, PS 100, SDR 26 (PS 115), PS140 and PS 200 with a solid, cellular core or composite wallĪSTM D3034 ASTM F891 ASTM F1488 CSA B182.2 CSA B182.4ĪSTM C14 ASTM C76 CSA A257.1 CSA A257.2Ĭopper or copper-alloy tubing (Type K or L) TABLE P3002.2 BUILDING SEWER PIPE MATERIALĪcrylonitrile butadiene styrene (ABS) plastic pipe in sewer and drain diameters, including SDR 42 (PS 20), PS35, SDR 35 (PS 45), PS50, PS100, PS140, SDR 23.5 (PS 150) and PS200 with a solid, cellular core or composite wall Forced main sewer piping shall conform to one of the standards for ABS plastic pipe, copper or copper-alloy tubing, PVC plastic pipe or pressure-rated pipe indicated in Table P3002.2. Stainless steel drainage systems, Types 304 and 316Līuilding sewer piping shall be as indicated in Table P3002.2. and a solid, cellular core or composite wall Polyvinyl chloride (PVC) plastic pipe with a 3.25 inch O.D. Polyvinyl chloride (PVC) plastic pipe in IPS diameters, including schedule 40, DR 22 (PS 200) and DR 24 (PS 140) with a solid, cellular core or composite wallĪSTM D2665 ASTM F891 ASTM F1488 CSA B181.2 TABLE P3002.1(1) ABOVE-GROUND DRAINAGE AND VENT PIPE MATERIALĪcrylonitrile butadiene styrene (ABS) plastic pipe in IPS diameters, including schedule 40, DR 22 (PS 200) and DR 24 (PS 140) with a solid, cellular core or composite wallĪSTM D2661 ASTM F628 ASTM F1488 CSA B181.1Ĭopper or copper-alloy tubing (Type K, L, M or DWV)ĪSTM B75/B75M ASTM B88 ASTM B251 ASTM B306 Allowance shall be made for the thermal expansion and contraction of plastic piping. Drain, waste and vent (DWV) piping in buildings shall be as indicated in Tables P3002.1(1) and P3002.1(2) except that galvanized wrought-iron or galvanized steel pipe shall not be used underground and shall be maintained not less than 6 inches (152 mm) above ground.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |